UltraPro Z-Wave Smart Vippljusomkopplare med QuickFit och SimpleWire, 3-vägs redo, kompatibel med Alexa, Google Assistant, ZWave Hub krävs, Repeater/Range Extender, Vit, 2-Pack, 54912 2-pack Light Switch Vit Vippströmbrytare

Name: UltraPro Z-Wave Smart Vippljusomkopplare med QuickFit och SimpleWire, 3-vägs redo, kompatibel med Alexa, Google Assistant, ZWave Hub krävs, Repeater/Range Extender, Vit, 2-Pack, 54912 2-pack Light Switch Vit Vippströmbrytare
Brand: UltraPro
SKU: 0030878549127
Price: 1217.78 SEK
Availability: InStock

Brand:UltraPro

3.5/5

€
1217.78

Håll kontakten med ditt hem med en UltraPro In-Wall Smart Switch. Den smarta switchen är kompatibel med alla Z-Wave-certifierade gateways och ger dig trådlös kontroll över dina fastanslutna lampor från vilken mobil enhet, dator eller Z-Wave-aktiverad fjärrkontroll som helst. Installationen är enkel – byt helt enkelt ut en vanlig strömbrytare i väggen mot den smarta strömbrytaren. Oavsett om du är hemma eller borta kan du komma åt strömbrytaren för att tända och släcka dina lampor. Den smarta omkopplaren hjälper inte bara till att minska energikostnaderna, den ökar även säkerheten i ditt hem genom att hålla rummen ljusa och levande. Ditt smarta hem har precis blivit smartare med UltraPro In-Wall Smart Switch.

Belopp

Lägg till i kundvagn Köp nu

EAN: 0030878549127

Kategorier Verkyg & hemförbättring, Elektrisk, Uttag, Uttagsbrytare,

KOMPATIBILITET - Fungerar med alla LED, CFL, halogen, glödlampor och andra enheter. INSTALLATION I VÄGG MED HÅRDA ANSLUTNINGAR (NEUTRAL KABEL KRÄVS) – Byt ut din befintliga strömbrytare i väggen på så lite som 15 minuter – Väggplatta ingår INTE. En neutral ledning krävs – vänligen bekräfta att ledningarna i ditt hem är kompatibla innan du köper (äldre hem kanske inte har neutrala ledningar). ALEXA KOMPATIBEL (HUB KRÄVS) - Kräver en Alexa-stödd hubb för röststyrning med Amazon Echo-produkter (Alexa-enhet och hubb säljs separat). Kan inte ansluta direkt med ECHO PLUS (Endast ZigBee-produkter kan ansluta direkt till Echo Plus). KRÄVER EN Z-WAVE CERTIFIERAD HUB - Kompatibel med följande Z-Wave Hubs: Honeywell, Ring, SmartThings, Wink, HomeSeer, Fibaro, Trane, Nexia, ADT, Vera och mer. TRÅDLÖST KONTROLLERA OCH SCHEMALAGA LAMPOR OCH ANDRA ENHETER – Schemalägg tidsinställda händelser för anslutna enheter. Anpassa scener för dag eller natt, hemma eller borta. Styr strömbrytaren trådlöst från var som helst via din smartphone, surfplatta, PC eller Z-Wave-fjärrkontroll. Omkopplaren kan manövreras manuellt.

Brand	UltraPro
Connector Type	Clamp
Contact Type	Normally Open
Country of Origin	China
Current Rating	15 Amps
Item Dimensions LxWxH	1.92 x 2.14 x 4.15 inches
Item model number	54912
Manufacturer	Jasco Products Company, LLC
Material	Polycarbonate
Operating Voltage	120 Volts
Operating Voltage	120 Volts (AC)
Operation Mode	ON-OFF
Product Dimensions	1.92 x 2.14 x 4.15 inches; 8.78 Ounces
Switch Type	Toggle
Terminal	Screw

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med^*

Ditt betyg

Scritto da: R. Levy

Very easy to integrate with SmartThings!

Open the SmartThings app and scan the sticker on the switch before you install. SmartThings will recognize the switch (although it called it a GE switch). Then once it powers up there is nothing more to do. SmartThings sees the switch and then you can integrate with whatever Home app you use with your SmartThings devices. I didn't have to do any toggles etc. as is sometimes necessary with these devices in order to find the device on the Z-wave network. For those that are interested, I installed this one in a housing box as pictured. The only problem was that the metal backplate on the switch was too large for this type of install, so I hacksawed it to align with the housing. Otherwise a straightforward install to replace an old Intermatic mechanical switch that is pretty outdated given the routines you can set up in SmartThings. I've installed a number of Zwave switches and although I can't speak yet to the reliability of this switch I did find that the initial set up was easier than some other devices.

Scritto da: Zeph

Same Hardware as GE, better price

These are the same Jasco Z-Wave switches that GE uses in their kit, just at a much better price. They integrated with HomeAssistant with no problems.

Scritto da: Diyengineer

Works so far

Purschased this to replace bad ge smart switches. Hoping these will last longer then ge brand. Also price is much better. Installation was easy and no hassle adding to smart things app.

Scritto da: Joe

Good ol Zwave.

Was looking for a replacement for an older GE jasco zwave switch that got toasted in a power outage. This one fit the bill. Was an exact match to the old one. And learning it was easy. Will buy again if I decide to Add more smart switches.

Scritto da: Jay_ATX

Works as good as GE and is compatible with Ring Alarm!

I needed to add some additional Zwave switches to my home but wanted something cheaper than the GE switches I had. These switches work the same as GE and are made by Jasco who also makes the GE Enbrighten switches. These also have a smaller profile than my original GE Zwave switches and paired easily to my Ring alarm. Installation was straightforward and took

Scritto da: toolseller

How to pair with SmartThings

For the SW4009 version, do the steps below to save hours: 1) Wire it up and install but leave faceplate off 2) do a factory reset even though it's new, flip toggle up 3 times, then down 3 times 3) in SmartThings app, find ur hub, select menu->Z wave utilities->z wave exclusion->flip toggle up and maybe down to get device excluded message. Maybe repeat...getting it excluded is KEY! 4) From a "room" in the app, select add a device. Browse by type->switch/dimmer->GE->GE z wave->next... 5) momentarily flip toggle up, then maybe down, and maybe repeat... usually works first time. You're not holding the toggle for this or any steps in this guide. 6) enter PIN from switch when prompted for the security function (u left cover off didn't u???).. don't bother trying to scan... 7) Success!!! Or try again from factory reset. You can now rename, move to another room, etc. 8) LED backlight is controlled in the Smart Things app. Select the switch and you can open the menu for the switch to control LED backlight function. I couldn't get it to work via directions provided with the switch by toggling the toggle. Finally, I've gotten a couple different versions of the "same item". This is what I FINALLY got to work with the noted part number. Factory reset and excluding from hub before adding to a room appear to be the key. Usually u don't have to keep toggling to get to pair but sometimes it helps, as does moving your hub close to the switch. If u can get the device excluded, ur well on ur way to success.

Scritto da: LearningMonkey

Same as GE for a lot less!

I saw these and thought this might be a cheaper option than the GE Embrighten switches that I have been getting. Not only are they cheaper, but they are EXACTLY THE SAME! I am pretty sure these are the exact same switches made by Jasco that GE offers. Features in the postings match up, they install in Smartthings as GE switches, and the printing/graphics on the face of the switch are the same! At $10 less per switch I will be getting these exclusively now. Thanks Ultra-Pro!

Scritto da: Myles

Switch was easy to install No customer service to help with software light switch integration!!!

Switch was easy to install No customer service to help with software light switch integration!!! On this I do not recommend this product!