TotalBoat Aluminium Boat Leak Sealer

Name: TotalBoat Aluminium Boat Leak Sealer
Brand: TotalBoat
SKU: 0811932022776
Price: 903.72 SEK
Availability: InStock

Brand:TotalBoat

3.3/5

€
903.72

Aluminiumbåtar lever hårda liv. De hamnar på stranden, träffar saker nedsänkta i vattnet och tenderar att användas i många år. Med tiden utvecklar nitar och sömmar läckor, sprickor eller till och med hål. En läckande aluminiumbåt kan sjunka snabbt. De flesta befintliga reparationsprodukter är tråkiga och tidskrävande. Deras instruktioner kräver att du belägger undersidan av båten. De hanterar inte flex eller stress bra, vilket leder till sprickor och fel på reparationen. TotalBoat Aluminium Boat Leak Sealer är annorlunda. Det är det snabba och enkla sättet att reparera läckande nitar, sprickor, sömmar och hål i din aluminiumbåt. Den kommer i en praktisk patron som passar i en vanlig tätningspistol. Stoppa bara in patronen i pistolen, fäst den medföljande blandningsspetsen på patronen, peka, dra i handtaget och kassera de första 3-4 tum av pärlan. Efter det kommer Leak Sealer ut blandad i exakt förhållandet 1:1 så att du får en ordentlig härdning och en vattentät tätning. Så enkelt är det att få rätt blandning – och pålitlig bot – varje gång. Om du bor i ett kallare klimat kommer du att uppskatta att du inte behöver vänta på att vädret ska bli varmare – du kan applicera Aluminium Boat Leak Sealer när aluminiumytan och den omgivande lufttemperaturen är så låg som 40°F, så länge som aluminiumytan har förberetts ordentligt. Aluminium Boat Leak Sealer är sjunkbeständig så den stannar där du lägger den och droppar inte ur sömmar och hål. Geltiden är 40 minuter vid 72°F. Böjhållfastheten är 8 800 psi. Tryckhållfastheten är 7 200 psi. Måla över härdade reparationer för maximalt skydd. Vänta 7-10 timmar innan du slipar och målar. Vänta 24 timmar innan härdad epoxi utsätts för höga belastningar. Jämför med West System G/Flex 650-K båtreparationssats i aluminium. Med TotalBoat finns det ingen mätning, ingen blandning, ingen röra och nästan ingen rengöring. Alla TotalBoat-produkter är utvecklade av båtfolk för båtfolk, för att ge stort värde och fantastiska resultat. Vi vet vad som fungerar och vad som inte fungerar.

Belopp

Lägg till i kundvagn Köp nu

EAN: 0811932022776

Kategorier Sport & utomhus, Industri & vetenskap, Sport & Fitness, Båt & segling, Båtar & Utrustning, Underhållstillbehör, Målningstillbehör,

Finns i en praktisk 250 ml. patron som bekvämt passar vanliga tätningspistoler. Inkluderar 2 statiska blandningsspetsar. Harts och härdare kommer i en enda patron och dispenseras automatiskt i rätt förhållande. Ingen blandning. Ingen röra att städa upp. Kan appliceras på korrekt förberedda aluminiumytor när luft- och underlagstemperaturen är så låg som 40°F. Lång arbetstid (75 minuter @ 72°F) säkerställer bättre penetration och bättre tätning. Absorberar påfrestningar från sammandragning, vibrationer, stötar och expansion som håller stadigt för att förhindra läckor. Lättanvänd, tvådelad, flexibel, vattentät epoxiförseglare reparerar läckande nitar och sömmar och lappar små hål på aluminiumbåtar snabbt och effektivt.

Brand	TotalBoat
Color	Buff
Compatible Material	Aluminum
Is Discontinued By Manufacturer	No
Item model number	497724
Manufacturer	TotalBoat
Material	Resin
Package Dimensions	9.92 x 2.87 x 1.93 inches; 13.76 Ounces
Style	Compact

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med^*

Ditt betyg

Scritto da: Kindle Customer

Easier to apply than other ratings implied

I bought this product to seal loose rivet leaks in my aluminum boat. I have not put the boat on the water yet, so cannot comment on how well it worked. That's why I gave it four stars and not five. I gave it four because the product was delivered promptly including a card asking for comments and offering a 20% coupon for future purchase as well as a product support phone number. Very nice service offer that at least appears as if the company - TotalBoat - is concerned about customer satisfaction. The product came well packaged and included two dispenser tips and a container that fits any caulk gun. Other comment had me a bit worried about being able to dispense the epoxy because I don't have great hand strength, however, cautioned by instructions on the tube I laid it in front of a heat duct while I prepared the surface and then had no trouble dispensing it at all. It was easy to get out of the tube, emerged as a not overly thick and easily pliable liquid that was very easy to manipulate, and ultimately made a nice layer that looks like a good seal. I applied it to rivets in the boat's floor then again on the bottom (so overhead). It stuck and stayed well in both locations. I've used Gluvit before and been very happy with it's property of filling in along the shaft of rivets as well as over the ends. This product is a little thicker, but it also had some flow so I'm hoping, but can't say for sure, that it did the same. In a week or two after I've finished this repair and installed the new floor, I will put the boat and the water. If it works as I hope, I'll change the rating to five stars. If not - well, you may see a new message in this space, but from all appearances I expect it to perform well.

Scritto da: Amazon Customer

Not mixing

I’m sealing the rivets on an aluminum Jon boat, the package states first 3-4 inches will be waste until mixed. I wasted first 5” just to be sure. For the next 40 rivets it seemed to work fine, then half way through it changed colors and I was only getting the orange/brown color assuming this is just hardener. So half my boat rivets got the epoxy side and the other half got just the hardener. Not happy with how it turned out because the first half I had to wipe off because there was no hardener. In the future I would buy a pre mixed boat epoxy from Home Depot.

Scritto da: Amazon Customer

Great product

I used this to seal some leaky rivets on a jon boat I recently acquired. Using a cheap caulk gun and the provided tips, it worked very well. It can be a little temperature sensitive so make sure you apply in conditions above 60 degrees. I did some application at that temperature and really killed my hand trying to squeeze the caulk gun trigger. I finished the job a few days later in warmer weather and found the application to be so much easier. The only thing to be aware of is that the tube can be a little misleading in size. It's only about 1/2 full, but I was able to seal every rivet on the bottom of my 14 boat, half the rivets on the inside, and several of the seams. It is however a caramel colored product and won't dry clear, so it will stand out that you've used it. That being said, it was perfect for my needs.

Scritto da: Real Customer

It seems to work

It takes more than 3 inches of material before it is properly mixed. Wait for the color to change to brown before applying it. It was white after 4 inches so I used it as it changed color. That section did not harden.

Scritto da: Jonathan Cowal

So far this has been a great product. I used it to seal every rivet ...

So far this has been a great product. I used it to seal every rivet and seam on an aluminum boat I was fixing. Some people have complained that it was difficult to dispense but I purchased the cheapest caulk gun I could find and it wasn't too bad. It was very easy to work with, I used a putty knife and was able to shape it easily around the areas I was working on. Also, it really does stay exactly where you apply it even when working on slanted or even upside down surfaces. Once sanded, I was able to paint over it and you cannot tell that there is anything there. I give it 4 stars because I have yet to test the boat out and I do not know how it holds up over time.

Scritto da: Kevin Vail

Very easy to use

I bought this to pro-actively seal the non-welded ribs on the hull of my 14ft v-hull. The mixing tip worked great. Each stick comes with two mixing tips in case you don’t use all of the compound in one instance. The compound is very easy to work with and apply and dries pretty quick for sanding and painting. So far I would highly recommend any product from this company.

Scritto da: MattG

Sealed up leaky aluminum boat

Worked well. I used it to seal a leaky riveted seam where the bottom of my aluminum boat meets the transom. Followed the instructions regarding surface prep, no problem squeezing it out with a standard cheapie caulking gun. Came out thin enough for me to force it into and through the seam with some compressed air, then gave it a thicker bead inside and out, then had plenty of time to smooth it. Took paint well. The following week, took it out to the lake, it sat in the water for 6 days with an hour or so of driving around each day, and no leaks at all. Very satisfied.

Scritto da: Barbara Bing

Takes some experience to apply

Did a good Job on leaks to an aluminum boat. Stuff is quite viscous and ease of application depends on size of opening. Used calking gun. Two nozzles to try with - you get better with time.