Mophorn 115V 230 V elmotor 56C Ram 1,5 hk elmotor 1725 rpm enfas elmotor 5/8 tums nyckelaxel för matchning av vattenpumpar 1,5 hk-uppgradering

Brand:Mophorn

3.3/5

6848.43

Flera tillämpningar: Elmotorerna används ofta inom industri- och jordbruksproduktion, transport, kommersiella och hushållsapparater och andra områden. Till exempel, matchning av vattenpumpar, jordbruksmaskiner, etc. Höghastighetskylfläkt: Stor fläkt i ena änden kyler motorn i timmars gång, även i dammiga eller fuktiga miljöer, vilket minskar energikostnader eller omkostnader, minskar driftstemperaturen, ökande lindningslivslängder. Stålhus: Kompressorns arbetsmotor är gjord av högkvalitativt stålmaterial. Det fasta och solida materialet kan skydda motorn väl, och det smidiga utseendet är lätt att rengöra; den inkluderar monteringsfästet, och fästets struktur är stabil och lätt att använda. Arbetseffektivitet: Elmotorn 56C kan köras med en maximal hastighet på 1725 rpm, hög arbetseffektivitet, Spänning: 115/230V 60 HZ, axeldiameter: 5/8 (1,6 cm), axellängd: 1,88 (4,8 cm), övre hårdhetsaxeln är mer hållbar. 1,5 hk elmotor: Denna kompakta och små växelströmsmotor har en effekt på 1,5 hk, 56C ram och enfas. Tätat kondensatorhus och ledningslådor skyddar alla miljöer.

Inga enheter tillgängliga
Flera tillämpningar: Elmotorerna används ofta inom industri- och jordbruksproduktion, transport, kommersiella och hushållsapparater och andra områden. Till exempel, matchning av vattenpumpar, jordbruksmaskiner, etc. Höghastighetskylfläkt: Stor fläkt i ena änden kyler motorn i timmars gång, även i dammiga eller fuktiga miljöer, vilket minskar energikostnader eller omkostnader, minskar driftstemperaturen, ökande lindningslivslängder. Stålhus: Kompressorns arbetsmotor är gjord av högkvalitativt stålmaterial. Det fasta och solida materialet kan skydda motorn väl, och det smidiga utseendet är lätt att rengöra; den inkluderar monteringsfästet, och fästets struktur är stabil och lätt att använda. Arbetseffektivitet: Elmotorn 56C kan köras med en maximal hastighet på 1725 rpm, hög arbetseffektivitet, Spänning: 115/230V 60 HZ, axeldiameter: 5/8 (1,6 cm), axellängd: 1,88 (4,8 cm), övre hårdhetsaxeln är mer hållbar. 1,5 hk elmotor: Denna kompakta och små växelströmsmotor har en effekt på 1,5 hk, 56C ram och enfas. Tätat kondensatorhus och ledningslådor skyddar alla miljöer.
Brand Mophorn
Country of Origin China
Horsepower 1.5 hp
Is Discontinued By Manufacturer No
Manufacturer Mophorn
Model Name Mophorn 115V 230 volt
Product Dimensions 14 x 8 x 8 inches; 38 Pounds
Speed 1725 RPM
Voltage 115 Volts

3.3

8 Review
5 Star
69
4 Star
10
3 Star
7
2 Star
3
1 Star
11

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med*

Scritto da: Mathew
clear instructions, simple wiring
spins if you plug it in.
Scritto da: MAUI
replacement motor
my original exhaust fan motor started sounding stressed, then in just wouldn't spin, I found this, the specs were comparable, so I got it, somehow there was a mix up with shipping, but the seller was able to get another shipped fast, Im not too savvy when it comes to wiring, so i found a tube video and it helped out big time, however the motor did come with instructions, so the video plus booklet together helped me understand what I was doing, super fast start up compared to my old motor, sounds strong, hopfully it lasts longer than my original!
Scritto da: 110 Motorsports
Purchased as a replacement for Ingersol Rand T5 air compressor
This motor is quite a bit smaller and mounting plat is flatter than it appears. The T5 mount is elevated. I took a flat piece of metal and notched out the holes to mate up to the compressor mount. Welded to the bottom of this. So far it has worked but prepare to make adjustments. Time will tell how well it holds up so I would rate it as average option to ingersol rand?
Scritto da: Amazon Customer
Seems to be great so far.
I run my air compressors very hard for sandblasting, and I normally buy expensive motors and pumps. This one was much lower priced, so I was a little skeptical, but I’ve had it running about 2 months now, it doesn’t get many breaks, and it’s doing great. I’m actually going to buy another one now.
Scritto da: Cabin Crow
PERFECT REPLACEMENT FOR OLD CAST IRON CRAFTSMAN TABLE SAW 113.29903
The OEM Craftsman motor gave up the ghost in the most stupid fashion, the shaft bent from snugging up the drive belt. Humming began, then intermittent start. Then finally, no start. Hum. Hmm. Took the thing apart and saw the commutator rubbing on the armature or whatever the guts are called. This is the PERFECT FIT and at 1.5 HP, I also bought the steel pulley for 5/8 shaft. That pulley is found here on Amazon. It is steel, has two set screws, and it comes with the square key stock, not a real 'woodruff key' since those have a curved side. That pulley is perfect too for this motor. Exact mount. Perfect. You will need a power cord so buy a new one, 14 gauge triple with the grounded plug 'for tools'. Then you will need a cord clamp / sheath cable connector with the screws so you can mount the cord and anchor it through the knock-outs on the motor's connection box. You will also need two wire nuts and a terminal -- spade type -- for the ground. Get yourself a new belt too. My saw's replacement belt is a Gates PoweRated 6841 / Industry Number 4l410K (1/2" x 41") = 12.5 to 13 mm x 1040 mm THIS HAS EASY TO READ WIRING INSTRUCTIONS on a double-sided, card stock, color printed document with all the models of single and three phase motors. You will easily be able to wire for 120 VAC or 230 VAC. Just read and take your time. If you're an old goat, put on your glasses. Only been running it a few days and if anything comes up, an update to the review will be posted.
Scritto da: Mark G.
Watch Out buying Refurbished
This motor said cosmetic imperfections... it was missing the fan! It has a thermal overload, so for now, it seems to be working ok. I am using this in a band saw. It is more noisy than the one that it replaced.
Scritto da: Alex
Great customer service
I don’t think I have ever written a review on Amazon but I wanted to say thanks for the awesome customer support. I bought this motor for my DIY plastic shredder at my house and it worked great the first day or so. There was a problem with the thermal reset and the company has sent me out a new motor to replace it with minimum hassle and a very quick turn over time. I would not hesitate to order from this seller again. I’m sure the new motor will work well for what I needed it was a perfect fit for my gear worm reducer 56C frame size. Thank you
Scritto da: Terry
Good replacement for husky air compressor
Works good for husky 80 gallon 3 cylinder compressor

Relaterade produkter

Upptäck vårt internationella nätverk

Vi skickar till 28 länder, över 200 000 produkter. Håll dig uppdaterad, prenumerera på nyhetsbrevet.

Array