LMT Onsrud 63-768 Solid Carbide Upcut Spiral O Flute, tum, obelagd (ljus) finish, 21 graders spiral, 1 räfflor, 2 0000 total längd, 0,1875 skärdiameter, 0,2500 skaftdiameter 3/16 tum

Brand:LMT Onsrud

2.8/5

933.50

PRODUKTBESKRIVNING Greenlee anställer stolt USA:s arbetsstyrka i sju tillverkningsanläggningar, där vi designar, monterar och tillverkar vissa produkter som uppfyller de rigorösa kraven i USA eller kvalificerande uttalanden. Vi uppmuntrar konsumenter att konsultera vår produktförpackning eller marknadsföringsmaterial som finns på greenlee för att förstå ursprunget för särskilda produkter. FRÅN TILLVERKAREN Greenlee DM-200 600 volt digital multimeter har automatisk mätning för bekväm användning, beröringsfri spänningsdetektering och för att spara tid. Datahåller och fångar mätningar. Automatisk avstängning och låg batteriindikator. RS-232-kapabel, kan anslutas till en PC för utökad mätkapacitet med valfritt optiskt isolerat gränssnitt DMSC-2. Visningsläge för relativ offset för att se relativa förändringar i mätningar. Frekvens-, temperatur- och kapacitansmätningar och AC-driftcykel. Tillbehör inkluderade två 1,5 volt AAA-batterier, testkablar och pärltemperatursond. Max 6000 spänningsmätning.

Inga enheter tillgängliga
Enkel flöjt, 21 graders vinkel. När de körs moturs (höger skärning) evakuerar spiralräfflade verktyg spån upp och ut ur snittet för att minska igensättning. Runda skaft tillåter användning med en mängd olika verktygshållningssystem. Obelagda verktyg har bara bassubstratet utan ytterligare behandling eller beläggningar och är lämpliga för ett brett spektrum av applikationer. Solida hårdmetallverktyg erbjuder lång livslängd och snabbare skärhastigheter än andra substrat, men är mer spröda och måste användas med styva verktygshållningssystem.
Country of Origin USA
Cutting Diameter 0.19 Inches
Cutting Length 0.63 Inches
Domestic Shipping Item can be shipped within U.S.
Finish Type Uncoated
Finish Type Uncoated (Bright)
International Shipping This item can be shipped to select countries outside of the U.S.
Item model number 63-768
Manufacturer LMT Onsrud
Material Carbide
Number of Flutes 1
Product Dimensions 4 x 0.5 x 0.5 inches; 0.8 Ounces

2.8

8 Review
5 Star
47
4 Star
18
3 Star
10
2 Star
9
1 Star
16

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med*

Scritto da: R. A. Jones
Nice cutter, shank is 1/4" despite the title and photo.
The title is a bit off because it says the shank is 0.125" when the specs say the shank is 1/4". The photo also shows a cutter with the shank diameter the same as the cutting diameter. It IS, however, 1/4" shank. I use it on a smallish CNC router with a 2hp spindle and it's worked quite well. In soft plastics like ABS I initially had the chip winding around the shank, melting and make a truly horrible cut. I built a new dust shoe to dramatically increase the air velocity around the cutter and with that dust shoe to keep the chips clear this cutter has worked very well.
Scritto da: Mississippi
Good bit
Nothing wrong with this one
Scritto da: Paul Haiducu
Arrived damaged!
I am not an expert in this, but the shop teacher I have worked with to drill holes in an aluminum plate tells me that the bit is damaged and cannot be used. Unfortunately, we have not carefully looked at the bit when it arrived (ordered on May 23, 2019), hence it is too late to return it or exchange it. It took the teacher a while to find time for the project I wanted done (we had the summer off, traveling, etc.). Yesterday, he realized that the bit is no good. The bit has not been used (and the shop teacher tells me that is obvious). These are not cheap, I am out almost $30.
Scritto da: Andrew D. Mowry
The description for this is incorrect. The 1/8” bit ...
The description for this is incorrect. The 1/8” bit has a 1/4” shank, not 1/8” as described and shown in the photo.
Scritto da: Seein Stripes
Great for HDPE on Bob's CNC E3
I now have about 20+ hours on the bit cutting and drilling .375" Starboard HDPE. I can say it is RAZOR sharp since it sliced my finger like a scalpel trying to remove some plastic shavings from around the bit. Runs straight and true at 45 ipm on my Bob's CNC machine.
Scritto da: Gary
This is the best bit I ever used on this material
I cut an aluminum composite material with this bit. The material is 2 aluminum skins bonded to a plastic center. This is the best bit I ever used on this material, a very clean, effortless cut.
Scritto da: Eric Varsanyi
Great cutter, clean edges on acrylic
This cuts acrylic like butter and leaves a very nice edge. I'm running a router at 18000 RPM with a feed rate of around 70 IPM and .06 depth cuts in cast acrylic.
Scritto da: bookbound93
Not 1/8 shank
Nice cutter, but needed a 1/8 shank and this is a 1/4 shank. Not happy.

Relaterade produkter

Upptäck vårt internationella nätverk

Vi skickar till 28 länder, över 200 000 produkter. Håll dig uppdaterad, prenumerera på nyhetsbrevet.

Array