AmpFlow P40-250-P Borstad elmotor, 250W, 12V, 24V eller 36 VDC, 3400 RPM

Name: AmpFlow P40-250-P Borstad elmotor, 250W, 12V, 24V eller 36 VDC, 3400 RPM
Brand: AmpFlow
SKU: 0680569239679
Price: 1319.18 SEK
Availability: InStock

Brand:AmpFlow

2.8/5

€
1319.18

AmpFlow P40-250-P är en pannkaksmotor med högt vridmoment designad för att leverera bra prestanda och effektivitet till ett ekonomiskt pris. Detta uppnås genom användning av fyra borstar och avancerad elektromagnetisk datormodellering och design. Motorn är 4,0 tum i diameter och 3,2 tum lång. Axeln går i två högkvalitativa kullager. De tunga motorkablarna är 14 tum långa. Motorn väger 4,2 pounds och den har en högkvalitativ svart pulverlack. Denna reversibla motor kan användas vid spänningar från 12V till 36Vdc. Vid 24 volt är tomgångshastigheten 3400 rpm. Den nominella uteffekten är 250W vid 2800 RPM vid 14 Amp. Maximal effektivitet är 78%. Denna motor levereras med en 13-tands remskiva för 5 mm HTD remAmpFlow®-motorer används i olika applikationer, inklusive robotar, elektriska skotrar, elcyklar och andra personliga transportsystem. Sök på Amazon efter AmpFlow-motorer för fler val.

Belopp

Lägg till i kundvagn Köp nu

EAN: 0680569239679

Kategorier Verkyg & hemförbättring, Industri & vetenskap, Elektrisk, Elektriska motorer, Permanenta magnetmotorer,

Kort pannkaksmotor med 13-tands remskiva för 5 mm HTD-rem. Toppeffektivitet vid 24V: 78%. Kontinuerlig effekt: 250 watt (1/3 hästkrafter). Varvtal utan belastning: 3400 vid 24 volt; Kan användas med spänningar från 12V till 36VDC. Mäter 4,0 tum i diameter (102 mm) gånger 3,2 tum lång (81 mm).

Country of Origin	USA
Item model number	P40-250-P
Manufacturer	Powerhouse Engineering Inc.
Package Dimensions	5.6 x 5.4 x 5.3 inches; 4.2 Pounds

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med^*

Ditt betyg

Scritto da: john angelosanto

is a ok motor

for generate dc power

Scritto da: A. W.

Probably ok if you need the pulley that comes with it.

I bought this motor with the intention of removing the pulley, as the seller stated was possible in one of the answered questions. Since the motor has a D shaft and a circlip, I assumed the pulley wouldn't be pressed on (or if it was, it wouldn't truly be an interference fit). I was wrong. On top of that, the pulley seems to be made of cheese grade sintered metal, which broke when I hit it with a hard rubber mallet (part of the flange broke off). I attempted to heat the pulley with a torch to remove it, but I'm afraid because the shaft is so small/short, I'll get the rest of the motor too hot and damage it. The motor is much noisier than I expected too, though I didn't run it until after I attempted to remove the pulley, so I can't be sure if that's because I damaged the bearings. All in all, $59 + tax wasted.

Scritto da: MRB1953

Good little motor

Good little motor. Operates smooth. Appears to be well made. Would be nice to have had some better documentation for it.

Scritto da: paul

Does the job

I am using it for a Ians BFF Shaker in a flight simulator so far so good. See how long it lasts

Scritto da: Michael Pare

Misleading Photo

I should have heeded the warning from another review that showed the one-sided pulley. AND in addition to that flaw it was also cracked upon arrival! I can't imagine what use-case a one-sided pulley would serve. For double the price of the motor without the pulley, this is bad. It cost me time and extra parts to get this going.

Scritto da: Enrique I

My pulley doesn't have one end.

The motor is ok, but the reason I put 3 stars is that the pulley in the ilustration and the pulley of the motor I received, are not the same. My pulley doesn't have one end. I attach some photos, so you can check the two pulleys are slightly different. Regards.

Scritto da: Donald Rogers

This is the best motor for the job.

I didn't dislike any part of it.

Scritto da: James Klingbile

works

Prompt delivery, item was as advertised