18-8 sexkantsflänsmutter av rostfritt stål, självlåsande tandad fläns med slät yta, ASME B18.2.2, 5/16-18 gängor (paket med 25) 5/16-18 1 1/4 tum 9/32 tum 0 tum 0 tum 25

Name: 18-8 sexkantsflänsmutter av rostfritt stål, självlåsande tandad fläns med slät yta, ASME B18.2.2, 5/16-18 gängor (paket med 25) 5/16-18 1 1/4 tum 9/32 tum 0 tum 0 tum 25
Brand: Small Parts
Price: 353.50 SEK
Availability: InStock

Brand:Small Parts

3.7/5

€
353.50

Uppfyller ASME B18.2.2-specifikationer. Vanlig yta har ingen finish eller beläggning. 18-8 rostfritt stål ger bra korrosionsbeständighet och styrka. Självlåsande tandad fläns gräver in i materialet som fästs för att förhindra att den lossnar. Flänsad bas eliminerar behovet av en bricka när komponenterna fästs, och sexkantskroppen dras åt från sidan med en skiftnyckel, vilket möjliggör användning när det finns begränsat utrymme ovanför muttern.

Belopp

Lägg till i kundvagn Köp nu

EAN:

Kategorier Industri & vetenskap, Spikar, Skruvar & Fästelement, Muttrar, Flänsmuttrar,

Exterior Finish	Stainless Steel
Fastener Type	Flange
Material	Stainless Steel
Metal Type	Stainless Steel
Thread Size	5/16"-18

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med^*

Ditt betyg

Scritto da: Kennaldo

They’re nuts

The nuts are great. Amazon, however, keeps sending me packs of 10 when I ordered 25. They let me keep the first pack of ten. They wanted the second 10 pack back. Curious to see if the third time is a charm. Third time was a charm, they finally sent me a pack of 25. I’m a happy camper.

Scritto da: Sharon Marchand

Easy fix

A hard to get piece of hardware that was needed to repair an expensive carriage wheel.

Scritto da: pat

Received package of 10- not 25:

Nuts arrived on time , however package o package of10-not 25.

Scritto da: phillip taylor

Good value

What can you say about nuts? All have good threads and fit the studs on our Polaris Sportsman 500. Better than buying from the dealer

Scritto da: Amazon Customer

Repurposed

Maybe I shouldn't write a review, as I did not use these as nuts. So, I can't say anything useful about the threads and such. However, I did use these as mixing weights in my (ceramics) slip container, and they work perfectly. The flanges cut through the lumps of clay as I shake the container. I can use 3 in 12 ounces of water/clay, and within a minute of shaking, have a really nice container of smoothly mixed slip. Since they're nice and heavy, they go to the bottom, out of the way. The finish on the nuts looks good, and has lasted very well - no rust or flaking.

Scritto da: Douglas H.

I never ever overspend

hi there , I just received these nuts and they look great and I was able to tighten up my trailer running board . with out any problems from these nuts . a really great value that should work as needed for a long time

Scritto da: Aleks M

Bolt threads eat into the nuts and seize them

Had the unfortunate joy of trying to remove these nuts. 1 in 5 nuts ended up cross threading when tightening using just a 1/4" hand ratchet. Then they wouldn't come off until I heated them with a torch and snapped them off with the bolts. Something was not right with the nuts I received. Thread pitch and everything was correct. The temper or something must be off since the bolt thread just bit right into the nuts when tightening.

Scritto da: Old Geezer

Non-rusting With Built In Washer and Locking Serrations--HIGHLY RECOMMENDED!

These nuts have a flanged base so you don't need a flat washer, plus they have serrations on the underside that help keep them from loosening. These are especially helpful when using carriage bolts where a nylock type lock nut may cause the bolt to spin, and would essentially be impossible to remove from an aged board.