Drill America - D/ACO3/4 3/4 koboltborr med reducerat skaft med 1/2 skaft, D/ACO Series 3/4 1/2 skaft

Name: Drill America - D/ACO3/4 3/4 koboltborr med reducerat skaft med 1/2 skaft, D/ACO Series 3/4 1/2 skaft
Brand: Drill America
SKU: 0887861005678
Price: 786.50 SEK
Availability: InStock

Brand:Drill America

3.2/5

€
786.50

Tillverkad av värmebeständig kobolt och slipad till en kraftig 135° splitpunkt. Gemensam räfflor och total längd för minimal justering vid verktygsbyten. Precisionsslipad för hög grad av koncentricitet mellan skaft och kroppsdiameter. Idealisk för borrning i tuffa material med hög draghållfasthet. Utökar storleksområdet för en bärbar borrchuck. Gemensam räfflor och total längd för minimal justering vid verktygsbyten. Precisionsslipad för hög grad av koncentricitet mellan skaft och kroppsdiameter. Idealisk för borrning i material med låg och medelhög draghållfasthet.

Inga enheter tillgängliga

EAN: 0887861005678

Kategorier Industri & vetenskap, El & handverktyg, Elverktyg & Tillbehör, Elektriska borrmaskiner Delar & Tillbehör, Borrbits, Twistbits, Jobber Drill Bits,

Tillverkad enligt National Aerospace standard 907. När de körs moturs (höger skärning) evakuerar spiralräfflade verktyg spån upp och ut ur snittet för att minska igensättning. Runda skaft tillåter användning med en mängd olika verktygshållningssystem. Guldoxid är en tunnare oxidytbehandling än svartoxid som vanligtvis används för att identifiera koboltstålverktyg; prestanda liknar obelagda verktyg. Koboltstålverktyg liknar snabbstål, men med mer kobolt för förbättrad prestanda vid skärning av hårdare metaller som rostfritt stål eller nickellegeringar.

Country of Origin	USA
Cutting Angle String	135 Degrees
Cutting Diameter	0.75 Inches
Finish Type	Gold Oxide
Is Discontinued By Manufacturer	No
Item model number	D/ACO3/4
Manufacturer	Drill America
Material	Cobalt Steel
Product Dimensions	6 x 1.3 x 1.2 inches; 1.16 Ounces
Shank Type	Round

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med^*

Ditt betyg

Scritto da: Wayne S.

Cobalt Hardened for Hard Metals

Cuts through stainless and hardened steels where titanium and others fail. Use some oil to preserve its edge for longer life.

Scritto da: Laura

Stainless steel

Just a couple of holes in 1/2" ss.

Scritto da: ratflinger

Quality bit

Bought a cheaper bit 1st - it failed immediately so I ordered this bit from Drill America. This bit drilled the 16 holes I needed and was still going strong at the end. Drill America bits stand up to the test.

Scritto da: GSD

Need a hole in your head?

Ok, maybe not the noggin! But for drilling steel this bit worked as a cobalt bit should. No issues, and it cut fast. Drilled through 1/4 plate steel pretty quickly using a 20 volt cordless drill. Quality seems good and was cheaper than big brand names. Like the reduced shank so i could use in 1/2" drill. Nothing worse then having a bunch of drill bits with the size worn off from slippage, so pick up a couple.

Scritto da: Mr. Geweke

worked well enough at a difficult task

Lasted about 2 hours of use against hardened steel before starting to dull. Would last a lot longer against mild steel and even longer with soft metals.

Scritto da: Earl Burns

Very sharp.

Drilled 15 holes through 1 in plate steel just fine. I used tap magic and a drill press.

Scritto da: Seth VanNuys

Legit

Had a project to drill 4x 5/8 holes in hardened steel. I had ordered 3 Cobalt hss bits from two different brands. Each failed drilling only about an 1/8" of the material. Ordered the bit from Drill America and finished the first hole in 20sec or less and went on to do the other three holes without issue using the single bit.

Scritto da: Mac user

Stepped shank drill doesn't run true

I bought a 33/64" stepped shank drill to cut close fit clearance holes for a 1/2-13 fastener. I mounted the drill on the 3 shank flats and noted significant runout (I'm guessing at least 1/16" runout) at the tip of the drill. So I tried mounting it on the 1/2" cylindrical surface. With the drill in that position, the bit cuts a hole that is 17/32" in diameter. So, it appears neither the stepped shank or the flats allow the drill to run concentric with the cutting tip. As a result I'll be avoiding Drill America bits in the future.

Scritto da: Richard

Well cutting!

As expected, fast delivery!