BOSCH ITBH201 1-delad 2 tum. Impact Tough magnetisk bitshållare 2 In. Standard 1-stycke

Brand:BOSCH

3.6/5

303.03

Hines, som erbjuds i fyra släta ytskikt, med två glasalternativ, är lämplig för en mängd olika dekorer. Övergångsstilen är ett äktenskap av traditionella silhuetter med moderna finish. Armaturerna i svart, gnidad brons, tenn och krom är ihopkopplade med skärmar av opal eller fröglas. Detta mini-hänge kan hängas individuellt eller monteras som ett set.

Inga enheter tillgängliga
Hög synlighetshylsa med laseretsade markeringar för användarens bekvämlighet. Värmebehandlad tillverkning för ökad hållbarhet. Avancerad design ger säker passform. Xtended Torsion Zone hjälper till att absorbera högt vridmoment från nya stötförare. 10X livslängd jämfört med standard slagbitar.
Brand BOSCH
Drive System Nutsetter
Item Dimensions LxWxH 0.47 x 1.75 x 1.01 inches
Material Metal
Size 2 In.

3.6

13 Review
5 Star
76
4 Star
14
3 Star
5
2 Star
2
1 Star
3

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med*

Scritto da: Jason
Misleading product photo
While this bit driver was what I was looking for, the photo shows 5 drivers. I admit it's my own fault for not reading the description saying 1 piece, but based off the photos I thought I was getting a heck of a deal. However for anyone who is tired of their bit pulling out of the driver everytime they screw in a screw this is perfect. The bit locks in just like the driver locks in to an impact drill.
Scritto da: Darren
A must have...
Anyone who uses a cordless drill or screwdriver needs this attachment. It holds many different bits without having to loosen the drill chuck. Also, it locks the bits in the holder so it will not come out during use.
Scritto da: Andy
Perfect quick disconnect addapter for my standard drill chucks!
Perfect for when I'm using my hex drive bits in my 3/8" drill chuck! Compact and fits in the standard hex bit holder. Perfect solution to make your drill chuck easy to use with your hex bits and not have to tighten and loosen it to constantly change bits. Hex-drive drill-bit or socket-driver changes are fast and effortless too. No more chuck-key or round shank drill bits to mess with or waist time when quick changes are needed. Holds them securely. Just pop 'em in and out, perfect!
Scritto da: Michael Ringer
it holds your bits!
This is so much better than the bit holders I used to use. This not only is magnetic but it also grips the bit so it won't fall out. So much better than the old school bit holders that are just magnetic.
Scritto da: Angela arnold
Good enough product
It was good for a week, but then the holder quit releasing the bits. I do a lot of construction and have been having issues finding a good quality one.
Scritto da: PaulW
Easy to use, holds bits tight.
I needed to be able to hold small bits in my impact driver. This works great, it holds the bits very securely. It's a good quality tool.
Scritto da: beka dogonadze
good
good
Scritto da: Amazon Customer
holds the bit
I got tired of the bit falling out of my magnetic bit holder. I've been using tape for years to add a little mechanical hold. This holder has a little snap ring to hold the bit. It holds it really well. Sometimes I might need a pair of pliers to pull the bit out, but I don't change it much. This works great for me.
Scritto da: Joiner/Carpenter
5 Pack ordered and 4 bent or badly assembled
4 out 5 of these holders were unusable, rotating out of alignment,. Surprised at Bosch for this. Other buyers with same problem. Returned
Scritto da: A. Parker
Great item and does what it’s supposed to do
Firstly this is what it is. It’s a bit pricey but good quality and would pay the same again quiet happily. Very happy with it.
Scritto da: Alex
Much better than magnetic part it replaced.
Great product.
Scritto da: Fioori
Não recomendo!
Em si o material aparenta ser bom fisicamente, porém vc logo vê que o ímã que é o principal requisito pra o produto, é muito fraquinho deixando até parafusos pequenos caírem, e a broca escolhida após encaixada 70% das vezes vc tem que remover com alicate pois fica preso, durabilidade muito boa pq vc quase não vai usar por isso dura bem. Não recomendo!
Scritto da: Jeremy Porter
Will not release the bit without using plyers
This seems like a simple and useful bit holder. However, when I want to take the bit out of this, it will not allow me to slide the release sleeve up to do so. I have to use plyers to pry on it. I'm not sure why it works this way. Perhaps I received a dud. I have another brand one and it releases the same bit without issue. So I would not recommend this one. Updating after some more use and it's just gotten worse. I have to pry the release open now with my vise. So there is nothing quick about this quick release. I've stopped using it as it's just garbage.

Relaterade produkter

Upptäck vårt internationella nätverk

Vi skickar till 28 länder, över 200 000 produkter. Håll dig uppdaterad, prenumerera på nyhetsbrevet.

Array